- "L" bracket flag mounting
- Two-wheeler frame mount
- Vinyl Flags in different colors
- Heavy Duty Balistic Nylon Flags
- Assorted Novelty Flags
- Glow in the Dark Flags
- HD Nylon Pirate, Nascar, Football Flags
For a complete discription and pictures of all the flag types available below click here
Flag $4.00 (Red Flag made from 18 mil banner material with printed logo)
I
tested about 20 different banner materials for durability before selecting
this one. I tested them by putting a flag on my truck with a solid pole
that did not flex so all the wind whipping was in the flag, then I drove
my truck for at least 20 miles at 70 mph, most that I tested did not make
it a mile before starting to unravel.
This American
Flag is made for Harley street bikes and it is made to last. It is double
layer nylon and is double sewn around the whole flag. The edge that usually
frays from whipping is sewn four times. The heavy white nylon slip that
your shaft goes through is twice as heavy a nylon as the flag it self.
This flag is made to last, not a cheap print that falls apart in a ride
or two. Comes with everything you need to put the flag on your whip. I
test this flag all the time, it is on my 650 that I ride both street and
dirt. This particular flag in this picture has over 1000 miles on it and
a lot of that mileage is at speeds of 70 mph or more. You will need at
least a 5/16" (.312) shaft to support this flag.
Axle flag mount for attaching a flag to your two-wheeler $9.95
This bracket is made from stronger and thicker aluminum than the competitors.
This bracket will fit almost all bikes except the small 50's through some
of the 100's. If you measure the axle bolt and it is 1/2" or smaller
you need the "L" bracket below drilled with two 1/2" holes.
Two-Wheeler side flag mount. $39.00
This mounting bracket (FlickWhip) is designed to mount with a new longer bolt into the existing bolt hole at the rear of your two-wheeler just before the rear fender. The second bolt is used after you drill a hole in the side of your rear fender to attach the mounting so it can not rotate downward. This is the best mount out there, there are some imititations that are shorter and I have found that they do not move the flag back far enough to allow the rider to use all of his/her seat without hitting the flag. This mount helps your whip last longer since it keeps the whip out of the tire. This bracket comes anodized in 3 colors beside natural aluminum.
This item only available in aluminum color only at this time
vPlain Vinyl flags in different colors. $4.00
Pennant flags 13 mm banner material, sewn with a sleeve to slide over your shaft. If you do not see the color you are looking for let me know and I will do my best to get it for you.
Heavy Duty Balistic Nylon flags in different colors. $10.00
Heavy duty Ballistic ripstop nylon 400 denier material double stitched all the way around. The finished size is 10-1/2" tall x 13" long. Sleeve fits up to 1/3" shaft. If you need a bigger sleeve or grommets I can make them. If you do not see the color you are looking for let me know and I will do my best to get it for you. I recommend that you have at least a 5/16" (.312) shaft or bigger for these flags.
Assorted Novelty Flags. 12" By 18" $6.50
These are polyester flags that are lightweight, printing on both sides with a sleeve so you can slide them over your shaft. Want a flag that is not listed let me know and I will get it for you if it is available.
For a complete discription and pictures of all the flag types available click here
These flags collect and store light by day and glow 2 to 4 hours in the dark. They are made of a rubberized material and then printed with a special glow in the dark ink. If they stop glowing in the dark you can recharge them by shinning your headlights on them for a couple of minutes and they will glow brightly again for another few hours.
For a complete discription and pictures of all the flag types available click here
Pirate, Nascar, Football Flags 12" X 18". $14.95
These flags are double layer nylon sewn twice around the edges and printed on both sides. These are very nice long lasting flags. You must have at least a 5/16" (.312) shaft to support these flags, as they are heavy duty and catch a lot of wind.
For a complete discription and pictures of all the flag types available click here
Last updated 06/3/15
